E46 series BMW 3

since 1998 of release

Repair and car operation



E46 series BMW 3
+ BMW 3 Cars (Е46)
- Current leaving and service
   Introduction
   Current leaving
   General information on control
   Check of levels of liquids
   Check of a condition of tires and pressure in them. Designation of tires and disks of wheels
   Replacement of impellent oil and oil filter
   Replacement of a filtering element of the air filter
   Checks of brake system
   Replacement of an element of the filter of air of salon
   Check of a condition of driving ridge belts
   Check of a condition and replacement of hoses of an impellent compartment
   Check of functioning of system of cooling and frost resistance of cooling liquid
   Check of a condition of system of production of the fulfilled gases
   Check of level of oil in a manual box of gear shifting
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts
   Check of level of liquid of system of hydrostrengthening of a wheel
   Visual check of a body and its bottom
   Check of seat belts
   Rotation and replacement of wheels
   Condition check, replacement of brushes and adjustment of a corner of screen wipers
   Check of a condition of the battery, care of it and charging
   Replacement of brake liquid
   Check and replacement of spark plugs
   Check of fuel system, replacement of the fuel filter. Operation of diesel model in the conditions of winter
   Greasing of loops and locks of doors
   Replacement of a battery of a key of remote control
+ Engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ engine Electric equipment
+ RKPP and transmission line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes



2d97642e


Checks of brake system

The dust being formed as a result of wear of slips and accumulating on components of the brake mechanism, can contain asbestos hazardous to health. Do not blow this dust by means of the compressed air and do not inhale it! Do not use solvents on the basis of gasoline for dust removal. The dust should be washed away a special cleaner of brake system or methyl alcohol in drain capacity. After rubbing of components of brake system by a damp rag this rag and contents of drain capacity should be kept in the closed and signed container. Further whenever possible try to use components not containing asbestos.

Except checks through the established intervals of time a condition of brake mechanisms it is necessary to carry out each time at removal of wheels or at emergence of signs of malfunction in system. For driving safety the checks of brake system described below procedure are most important of all procedures made by you on car service.


Signs of malfunctions in brake system

1 Disk brake mechanisms can have the built-in indicators of wear of frictional slips which signal that wear of slips reached critical size. Thus slips should be changed immediately, differently brake disks will be damaged and they will need expensive repair.
By 2 Liouba from listed below signs can point to potential defect of brake system:

a) When squeezing a pedal of a brake the car "withdraws" in one party
b) Brake mechanisms when braking publish scraping or squealing sounds
c) The pedal of a brake has an excessive course
d) The pedal of a brake pulses (it normally only at ABS system work)
e) Leakages of brake liquid (usually on tire or wheel inside) are observed
3 in case of detection at least one of these signs immediately examine brake system.

Brake lines and hoses

In brake system steel brake tubes, except for the flexible reinforced hoses at forward wheels and as connections at the back bridge are generally used. Regular survey of all these lines is very important.


4 Park the car on an equal platform and switch off the engine. Remove caps from wheels. Weaken, but do not remove bolts of fastening of all four wheels.
To 5 Poddomkratta the car and reliably establish it on support.
6 Remove wheels (address to the Section Rotation and replacement of wheels).
7 Check all brake lines and hoses on existence of cracks and attritions in their external covering, leaks, swellings and deformations. Check brake hoses in forward and back parts of the car on existence of signs of a softening, cracks, deformations or wear as a result of a friction about other components. Check all shtutserny connections on existence of signs of leaks and make sure of reliability of fastening of all bolts and clips of brake hoses.

8 Bend hands in one and other parties a brake hose to reveal damages. To braid hoses does not follow. Watch the direction of the color line put on a hose.


9 Turn a steering wheel to the right and to the left against the stop. Hoses should not touch elements of a design of the car thus.
10 At detection of leakages of liquid or their damages it is necessary to eliminate immediately. For more detailed description of procedure of repair of brake system address to Head Brake system.

Check of thickness of brake shoes


At wear of brake shoes of lobbies and back brakes on the dashboard the signaling device lights up. Thus it is necessary to replace brake shoes urgently.

Operation of lifting and car installation on supports is connected with danger! Therefore before carrying out operation familiarize with Poddomkrachivaniye's Section and towage


11 Mark paint the provision of wheels concerning a nave. It will allow to establish at assembly otbalansirovanny wheels in their former situation. Weaken bolts of fastening of wheels on the car standing on the earth. Lift the car, put it on supports and remove wheels.

Disk brake mechanisms

12 Check visually thickness of blocks without a metal plate, looking from above through a support.

13 In addition check sideways thickness of an external block. A limit of wear of blocks of forward and back brakes will reach, if the thickness of a block makes 3 mm.


14 In doubtful cases remove blocks and measure thickness by a calliper. At achievement of a limit of wear of a block it is necessary to replace. Thus it is necessary to replace all four blocks of one axis even if the limit of wear was reached by only one block.

On the basis of experience it is known that 1 mm of wear of a block of a disk brake corresponds 1000 km of run. It corresponds to adverse service conditions. At normal operation of the car service life of blocks much more. At thickness of a block in 5.0 mm (without a podkladny plate) the block can be still used for run of 2000 km.


15 Check, whether has a support of traces of leakages of brake liquid. In the presence of a leakage urgently hand over a support in repair.
16 Visually check brake disks from the internal and external parties on existence задиров, corrosion damages and cracks. If necessary replace disks.

Parking brake

17 Blocks of the parking brake can be checked visually after removal of a disk of a working brake. A limit of wear will reach, if the thickness of a block in the thinnest place makes 1.5 mm.


18 If a limit of wear will reach, it is necessary to replace blocks. Surely replace all blocks of one axis, address to the Section Removal and installation of blocks of the parking brake.
19 Establish wheels so that the markings put at removal coincided. Previously grease with a thin layer of bearing greasing aligning belt of a disk of a wheel on a nave. Bolts of fastening of a wheel do not grease. It is necessary to replace rusty bolts. Establish wheels and wrap fastening bolts. Lower the car on wheels and tighten bolts cross-wise the moment of 100 N • m.

Check of functioning of the parking brake

The parking brake represents a drum-type brake with a hummock drive. The drum is built in disks of a back brake. As wear of a brake shoe of the parking brake is insignificant, corrosion damage or pollution of brake shoes can take place. Therefore before check of the parking brake it is recommended to earn extra it as follows:

20 Smoothly brake the car the parking brake since speed of 40 km/h on the desert street or a parking platform so. Without changing speed, tighten the parking brake on one tooth and pass 400 more m. Release a brake and let's to it be cooled.

Operation of lifting and car installation on supports is connected with danger! Therefore before carrying out operation familiarize with Poddomkrachivaniye's Section and towage


21 Lift and establish on supports a back part of the car. Wheels should be over the earth at height not less than 2 see.
22 Tighten the parking brake on one click and turn back wheels. Wheels should be turned freely, brakes should not work.
23 When raising brake on 10 clicks of a wheel should затормаживаться completely.
24 Otherwise adjust the parking brake, address to the Section Adjustment of the parking brake.
25 Lower the car on wheels.