E46 series BMW 3

since 1998 of release

Repair and car operation



E46 series BMW 3
+ BMW 3 Cars (Е46)
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ engine Electric equipment
+ RKPP and transmission line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   + Forward suspension bracket
   + Back suspension bracket
   - Steering with the hydraulic booster (servoupravleniye)
      Removal and installation of the block of a safety cushion on a steering wheel
      Removal and installation of a steering wheel
      Removal and installation of a tip of steering draft
      Removal and installation of steering draft
      Removal and installation of the pump of the hydraulic booster
      Filling with liquid and air removal from hydrosystem of the amplifier of a wheel
      Corners of installation of forward wheels. Check of installation of wheels
+ Body
+ Onboard electric equipment
+ electric equipment Schemes



2d97642e


Removal and installation of a tip of steering draft

Steering mechanism, covers and steering drafts

1 — steering draft right
2 — vрулевая draft left
3 — nut М12, 65 N • m
Being self-stopped, surely replace
4 — a set of covers of the steering mechanism right
5 — the steering mechanism
6 — a set of covers of the steering mechanism left
7 — a tip of steering draft
8 — a ring tightening

9 — a nut of tightening, 80 N • m
10 — a collar, Ø50 – 53 mm
11 — a ring basic
It is inserted into narrowing of steering draft near a six-sided nut. Before installation of steering draft grease it with konsistentny greasing at narrowing that at turn of draft to exclude joint rotation of a cover.
12 — a cover
13 — a collar, Ø65 – 68 mm


 REMOVAL

1 Mark paint the provision of a forward wheel concerning a nave. It will allow to establish an otbalansirovanny wheel in the former situation. Weaken bolts of fastening of a wheel at the car standing on the earth. Lift a forward part of the car and remove a wheel.

2 Measure the size - And - between the hinge and the end of a carving of steering draft
- 5-also write down the received value.

3 Weaken a tightening nut-1-tips of steering draft-2-, address to the Section Corners of installation of forward wheels. Check of installation of wheels.

4 Unscrew a nut of fastening-3-hinges of steering draft-4-. 2–tip of steering draft.

5 Remove a tip of steering draft by means of the HAZET779 tool – 1.

6 Unscrew a tip from steering draft, keeping thus draft a wrench for a shestigrannik-5-from a provorachivaniye.

At an otvorachivaniye count number of turns and write down the received value. It will facilitate further adjustment of forward wheels.


 INSTALLATION

7 Establish on steering draft a tightening ring if it acted in film.
8 Screw a tip of steering draft, the number of turns should be equal to number of turns at removal. Check the size - And - received before removal.
9 If it is necessary, clear of greasing a pin of the hinge of steering draft, and also an opening in a rotary fist.
10 Insert a tip of steering draft, and also an opening into a rotary fist. Screw a new being self-stopped nut on a pin of the hinge and tighten it the moment of 65 N • m.
11 Tighten a tightening nut of a tip of steering draft the moment of 80 N • m. Thus keep draft from a provorachivaniye for a shestigrannik.
12 Establish into place a wheel so that the markings put at removal, coincided. Previously grease with a thin layer of bearing greasing a seat of a disk of a wheel on a nave. Bolts of fastening of a wheel do not grease. Rusty bolts replace with the new. Fix a wheel bolts. Lower the car on wheels and tighten bolts cross-wise the moment of 100 N • m.
13 Check a track on HUNDRED, if necessary adjust.